Sponsored
OP
OP
shine

shine

Trailhunter
Well-known member
First Name
Chris
Joined
Mar 8, 2025
Threads
4
Messages
279
Reaction score
267
Location
Seattle
Vehicle(s)
2025 4Runner Trailhunter, 2008 4Runner SR5
I did indeed remove the rear spoiler, there’s a picture in the original post where the spoiler is on the ground and I’m drilling holes and mounting the rear camera.

I do not however remember how I fished the wire through on the left side of the rubber hose, no recollection of there being tape around the wire bundle as it exits the rubber hose on the hatch side.
Sponsored

 

ifunlisted

Platinum
Well-known member
Joined
Nov 6, 2025
Threads
1
Messages
86
Reaction score
17
Location
AZ
Vehicle(s)
4Runner
Decided to install a Redtiger dash cam with an external rear camera and a hard wire kit. I've used an older model with the same setup on my 4th gen without any issues, so decided to do the same with my new 4Runner. Here's what I started with:

IMG_7238.webp

That's the rear camera, main unit, and hardwire kit in the front. Behind the hard wire kit is a Subaru harness that I used to power the dash cam off the plug that's already behind the headliner by the roof console.

You can all these items from Amazon:
Redtiger F7N Elite https://a.co/d/1z1Q3zo
Hardwire kit https://a.co/d/2ZwgWQq
Subaru harness H501SSG010 https://a.co/d/bFwdYbL
You can probably get the Subaru harness for less from your local Subaru dealer, that's what I did - https://parts.subaru.com

Before doing anything else I used the 12v cigarette lighter connector that came with the camera (not shown above) to power up the dash cam and rear camera to test. It all worked as expected.

Started by creating the wiring harness for the dash cam. Checked the connector inside the headliner with a multimeter to make sure I had the right connector before started. Cut the Subaru harness and the hardwire kit and connected them with spade connectors. Added some shrink wrap on top of the connectors for good measure.
IMG_7244.webp


To get access to the connector above the headliner, remove the roof console by pulling down on the front. That is the side towards the windshield. I used a trim tool to help me get a grip around the front edge and pulled it down with my fingers and left it hanging by the wiring already in place.
IMG_7242.webp


Here you can see the existing dash cam connector
IMG_7243.webp


Next, I started pulling the cable to the rear camera. Using an wire hanger cut and straightened out I pulled the cable from the roof console towards the driver's door.
IMG_7245.webp
IMG_7246.webp


Doing this I was able to avoid the A pillar completely. However, when you peek under the headliner by the driver's door you'll notice the airbag up there. Be careful not to trigger it and be careful not to obstruct its function with the cable. You want to route the cable behind the airbag.
IMG_7248.webp


For the final stretch towards the rear I loosened the D pillar trim and pushed the coat hanger tool towards the rear door. Had to try a couple of times before I could get the coat hanger to where I could grab it, but got it eventually. Never had any problems with the coat hanger snagging, but I made sure to close the loop around the cable every time before pulling the coat hanger with the cable attached.

At this point I removed the rear spoiler from the rear door. Found a good description of how to do that on Westcott's 2025 4Runner Ladder Install Video 6th Gen.

Now to the hardest part, getting the cable through the rubber hose between the back of the roof and the door. I pushed my coat hanger tool from the left to the right, very carefully to not damage any of the other wires in the rubber hose, and after disconnecting it from both the door and the roof of the car. This is also the only place where I damaged any part of the car, one of the tabs on the white plastic part securing the rubber hose to the roof broke off. Not too worried, was able to seat the part sufficiently after I finished the install. Reconnect the hose back after you've put the wire through.

IMG_7251.webp


Now to the fun part, drilling holes into my new 4Runner...
IMG_7254.webp


Now double-check that all the clips are where they need to be and put the rear spoiler back on again. The camera is connected to the cable that you just pulled from the front of the cab with a four pin connector. I left this connector inside the spoiler to make it easy to disconnect again. You could always put some tape or heat shrink around this connector if you're concerned about moisture ingress. I decided not to do that, at least not for now.

Also, this is a good time to remove slack from the cable you and pull excess into the opening where the roof console belongs. Pull the rear camera cable and usb-c power cable under the headliner to where you want to mount the dash cam and zip time up any excess cable. There's plenty of space above the headliner for the excess cable.
IMG_7256.webp


Clean the inside of the windshield and stick the dash cam where you want it! Connect the rear dash cam and power cables to the dash cam and pull excess back in to the cavity inside the headliner before putting the roof console back on.

That's it! Here's what my dash cam and rear cam look like:
IMG_7257.webp

IMG_7258.webp


And here's what it looks like from the driver's seat:
IMG_7260.webp
Have you run into any issues with parking mode shutting off within a minute or so? I'm using the same harness and for some reason my camera starts into parking mode just fine when I turn off the vehicle but after a minute or so it turns off (basically right after the headlights turn off after the follow me home delay).
 

BonRunner

TRD Sport Premium
Well-known member
Joined
Dec 2, 2025
Threads
18
Messages
630
Reaction score
714
Location
Montana
Vehicle(s)
2026 TRD Sport Premium / WCP
Have you run into any issues with parking mode shutting off within a minute or so? I'm using the same harness and for some reason my camera starts into parking mode just fine when I turn off the vehicle but after a minute or so it turns off (basically right after the headlights turn off after the follow me home delay).
You need a Dongar Pro adapter, https://dongar.tech/products/Dongar-Pro.

It plugs straight to Toyota system. No need to mess with old school hardwired method.
 

ifunlisted

Platinum
Well-known member
Joined
Nov 6, 2025
Threads
1
Messages
86
Reaction score
17
Location
AZ
Vehicle(s)
4Runner
OP
OP
shine

shine

Trailhunter
Well-known member
First Name
Chris
Joined
Mar 8, 2025
Threads
4
Messages
279
Reaction score
267
Location
Seattle
Vehicle(s)
2025 4Runner Trailhunter, 2008 4Runner SR5
Have you run into any issues with parking mode shutting off within a minute or so? I'm using the same harness and for some reason my camera starts into parking mode just fine when I turn off the vehicle but after a minute or so it turns off (basically right after the headlights turn off after the follow me home delay).
Have not run into any issues with parking mode.

Just tested it by bumping the camera after the car has been parked overnight, simulating someone hitting my parked car. Camera did indeed start recording.

Suggest a couple of ways to troubleshoot, one is to make sure the always hot 12v wire is indeed hot after your headlights have turned off. If it isn't, then make double sure that you're tapping into the right wire on the connector.

Also, recommend making double sure that your camera is configured for parking mode.
 
OP
OP
shine

shine

Trailhunter
Well-known member
First Name
Chris
Joined
Mar 8, 2025
Threads
4
Messages
279
Reaction score
267
Location
Seattle
Vehicle(s)
2025 4Runner Trailhunter, 2008 4Runner SR5
You need a Dongar Pro adapter, https://dongar.tech/products/Dongar-Pro.

It plugs straight to Toyota system. No need to mess with old school hardwired method.
The method that I described in this thread plugs straight into the Toyota dash cam connector that's already in our vehices.

Last time I checked the Dongar adapter didn't support parking mode. It simply keeps recording as if you're still driving for either a specific amount of time or until the battery voltage reaches a certain level. That's not what I want.
 

ifunlisted

Platinum
Well-known member
Joined
Nov 6, 2025
Threads
1
Messages
86
Reaction score
17
Location
AZ
Vehicle(s)
4Runner
The method that I described in this thread plugs straight into the Toyota dash cam connector that's already in our vehices.

Last time I checked the Dongar adapter didn't support parking mode. It simply keeps recording as if you're still driving for either a specific amount of time or until the battery voltage reaches a certain level. That's not what I want.
Thanks Chris. Yep I think the Dongar is a nice simple option but in my case no adapter that fits my camera. I also prefer fewer variables and want to make sure I have parking mode... so the existing Toyota connector is ideal.

My camera is a Vueroid S1 which is somewhat new in the US but it's very good and the company has been outstanding, they've responded to every question I've had within 24hrs. It turns out that my issue is most likely just how their software is set up. They have an Extreme Low Power Mode (ELPM) that kicks in if you reach a voltage threshold, and when that happens the LED light on the camera also turns off even though the camera's still on. I have mine set to go into that ELPM immediately, so my LED turns off after about 60 seconds, which also happens to be right around the same time as my headlight delay. I'm going to test it a little today to make sure it still records in parking mode even though the light is off but that all makes sense.

Really appreciate all the info and photos you provided. I found another compatible connector and a good mounting option that I'll post once I've had a chance to test everything a little longer.
 

ifunlisted

Platinum
Well-known member
Joined
Nov 6, 2025
Threads
1
Messages
86
Reaction score
17
Location
AZ
Vehicle(s)
4Runner
The method that I described in this thread plugs straight into the Toyota dash cam connector that's already in our vehices.

Last time I checked the Dongar adapter didn't support parking mode. It simply keeps recording as if you're still driving for either a specific amount of time or until the battery voltage reaches a certain level. That's not what I want.
Hey Chris! When you were working on this did you happen to trace the factory dashcam harness to the fusebox for any reason, and if so do you remember how many amps the fuse was? I might try to connect a dash cam battery pack using that harness but they draw a little more power than cameras. Thanks.
 
OP
OP
shine

shine

Trailhunter
Well-known member
First Name
Chris
Joined
Mar 8, 2025
Threads
4
Messages
279
Reaction score
267
Location
Seattle
Vehicle(s)
2025 4Runner Trailhunter, 2008 4Runner SR5
Hey Chris! When you were working on this did you happen to trace the factory dashcam harness to the fusebox for any reason, and if so do you remember how many amps the fuse was? I might try to connect a dash cam battery pack using that harness but they draw a little more power than cameras. Thanks.
I'm afraid I did not try to trace it. Best guess a 2 day subscription to https://techinfo.toyota.com/ should give you the wiring diagrams you need.

That said, what is the purpose of the dash cam battery pack?
 

ifunlisted

Platinum
Well-known member
Joined
Nov 6, 2025
Threads
1
Messages
86
Reaction score
17
Location
AZ
Vehicle(s)
4Runner
I'm afraid I did not try to trace it. Best guess a 2 day subscription to https://techinfo.toyota.com/ should give you the wiring diagrams you need.

That said, what is the purpose of the dash cam battery pack?
Ok I'll try it out! The battery pack is mainly just to get longer durations in parking mode. The plan is to connect that through the dash cam harness since it has all the necessary wires, then connect the camera to the battery pack. That way the camera will be powered by the 12v dc from the car (passed through the pack) while the car is running, but then when the car is turned off the camera will be powered by the battery pack. Much longer recording time and less direct interaction with the car battery.
 

josiahg52

Trailhunter
Well-known member
First Name
Josiah
Joined
Jun 6, 2026
Threads
3
Messages
435
Reaction score
229
Location
Maine, United States
Vehicle(s)
2026 Trailhunter, 2018 Ram 2500, 2001 BMW M5, 2001 BMW X5 35d
How is parking mode provided? It must be a camera function?
 

ifunlisted

Platinum
Well-known member
Joined
Nov 6, 2025
Threads
1
Messages
86
Reaction score
17
Location
AZ
Vehicle(s)
4Runner
The battery pack still gets the same two inputs from the vehicle that the camera would get (Continuous 12V and Switched Accessory). It takes those two sources and becomes the 'middle man', so when you connect the camera to the battery pack, the camera still gets both signals and lets it know when it should be in normal 12v recording mode vs when it should switch to ACC parking mode. That's why it's important to use battery packs specifically designed for dash cams... other generic batteries won't communicate those signals.
Sponsored

 
 







Top