Panda 2.0! TRD ORP Build on 35's

[Ramrod113]

Panda 2.0 has been completed.

Westcott Preload collar lift.
Method 703 Matte Black 17x8.5 +35 offset
35x12.50r17 Toyo Open Country AT3 (C load)
ARB 2.5m awning
Lasfit LED turn signals
Lasfit cargo liners for the rear seat backs
Factory Toyota Red recovery hooks (front)
3D printed goodies here and there (by me, hit me up if interested)


Panda 2.5/3.0 plans:

Rock Sliders (undecided brand)
Front bumper (undecided brand)
Rear swing out (undecided brand)
A full suspension (preferably Dobinsons)
Full roof rack (Prinsu or Westcott)

Sponsored

 

[boneskid1]

What accessories have you 3d printed? I was looking to see if anyone had designed anything that I might find useful for my ORP.

 

[Ramrod113]

What accessories have you 3d printed? I was looking to see if anyone had designed anything that I might find useful for my ORP.

All the emblems I have. Also a few interior trim rings that go around the climate control and drive mode selector.

 

[porkyfly]

What raptor grille lights are those?

 

[Flexte]

What raptor grille lights are those?

lokloks like these https://www.amazon.com/Grille-Lights-Toyota-Accessories-24Tacoma-Amber/dp/B0DLL9BQ17

 

[Ramrod113]

What raptor grille lights are those?

https://a.co/d/dFQsqyL

 

[DangItsDen]

Panda 2.0 has been completed.

Westcott Preload collar lift.
Method 703 Matte Black 17x8.5 +35 offset
35x12.50r17 Toyo Open Country AT3 (C load)
ARB 2.5m awning
Lasfit LED turn signals
Lasfit cargo liners for the rear seat backs
Factory Toyota Red recovery hooks (front)
3D printed goodies here and there (by me, hit me up if interested)


Panda 2.5/3.0 plans:

Rock Sliders (undecided brand)
Front bumper (undecided brand)
Rear swing out (undecided brand)
A full suspension (preferably Dobinsons)
Full roof rack (Prinsu or Westcott)

So clean dude! Which lugs did you go with for the Methods? They recommend these extended ones, but they seem like they would poke like hell. https://www.methodracewheels.com/products/lug-kit-black-spline?variant=55157766455665

 

[Ramrod113]

So clean dude! Which lugs did you go with for the Methods? They recommend these extended ones, but they seem like they would poke like hell. https://www.methodracewheels.com/products/lug-kit-black-spline?variant=55157766455665

Yeah I used the extended. They don’t look extended at all so I’d hate to see what the non-extended looks like.

 

[dystynkt]

Beautiful build so far!

 

[Ramrod113]

Beautiful build so far!

Thank ya!

 

[Van Solo]

Panda 2.0 has been completed.

Westcott Preload collar lift.
Method 703 Matte Black 17x8.5 +35 offset
35x12.50r17 Toyo Open Country AT3 (C load)
ARB 2.5m awning
Lasfit LED turn signals
Lasfit cargo liners for the rear seat backs
Factory Toyota Red recovery hooks (front)
3D printed goodies here and there (by me, hit me up if interested)


Panda 2.5/3.0 plans:

Rock Sliders (undecided brand)
Front bumper (undecided brand)
Rear swing out (undecided brand)
A full suspension (preferably Dobinsons)
Full roof rack (Prinsu or Westcott)

Would Love The TRD logo in Black to add to the same spot you did!
On the Front Bumper Insert.....

 

[Ramrod113]

Would Love The TRD logo in Black to add to the same spot you did!
On the Front Bumper Insert.....

Sent you a direct message.

 

[6GenChad]

Panda 2.0 has been completed.

Westcott Preload collar lift.
Method 703 Matte Black 17x8.5 +35 offset
35x12.50r17 Toyo Open Country AT3 (C load)
ARB 2.5m awning
Lasfit LED turn signals
Lasfit cargo liners for the rear seat backs
Factory Toyota Red recovery hooks (front)
3D printed goodies here and there (by me, hit me up if interested)


Panda 2.5/3.0 plans:

Rock Sliders (undecided brand)
Front bumper (undecided brand)
Rear swing out (undecided brand)
A full suspension (preferably Dobinsons)
Full roof rack (Prinsu or Westcott)

How much of that bottom fender did you trim? The shop I had mine done at trimmed maybe a little less than an inch, but im worried when I wheel it, it'll rub up against where the fender starts.

 

[Ramrod113]

How much of that bottom fender did you trim? The shop I had mine done at trimmed maybe a little less than an inch, but im worried when I wheel it, it'll rub up against where the fender starts.

I only trimmed off the 2 existing tabs on each side so 4 total tabs. They are left over after pushing the liner forward.

Sponsored