Sponsored

Combining Multiple Lights on Factory AUX Switches. Wiring suggestions?

Clipse

TRD Off-Road Premium
Well-known member
Joined
Jul 28, 2025
Threads
2
Messages
48
Reaction score
34
Location
Seattle, WA
Vehicle(s)
2025 4Runner
Hey everyone,

Looking for some advice from anyone who's wired up auxiliary lighting on the 6th gen 4Runner Hybrid, specifically using the factory Toyota AUX switches.

With BF around the corner, I'm planning to run:
  • 2x Baja Designs Squadron 2.0 Sport ditch lights
  • 1x Baja Designs 20” S8 light bar (lower Pro grille)
Ideally, I'd like to keep everything running through the factory AUX switches and Toyota pigtails. I'm trying to avoid adding something like a SPOD or Switch-Pros at this point, since I don't anticipate having a ton of additional accessories to wire up down the road.

My initial thought was to put all the main lights (both ditch lights + light bar) on one AUX switch, and all the backlight functions on another. That way, I can turn on the main lighting together, or just run the backlights independently.

A couple questions:
  1. Has anyone done something similar using AUX 1/2 vs AUX 3/4? Is there a reason to favor one set of switches over the other?
  2. Is there any reason I shouldn't combine the two ditch lights and the S8 light bar onto one AUX circuit? I can't really see this as an either/or situation. If I'm in a situation where I need the ditch lights, I'd probably want the light bar on as well. Seems more useful to have them come on together rather than use two separate switches.
  3. From an electrical standpoint, is the combined draw too much for a single factory AUX circuit?
  4. For the backlights, can the two Squadron backlights and the S8 amber backlight be tied into a single AUX switch? Any quirks with the Baja Designs harnesses I should be aware of?
Mostly looking for recommendations on how others have approached this, especially if you've done it on the Hybrid with the factory AUX wiring. I've been going back and forth on this idea for a while and needed to recruit your expertise and guidance.

Appreciate any advice, wiring diagrams, or pictures of your setups. Thanks!
Sponsored

 

josiahg52

Trailhunter
Well-known member
First Name
Josiah
Joined
Jun 6, 2026
Threads
3
Messages
434
Reaction score
229
Location
Maine, United States
Vehicle(s)
2026 Trailhunter, 2018 Ram 2500, 2001 BMW M5, 2001 BMW X5 35d
You can hook up whatever you want. The AUX switches have ratings and they're not all the same. To get around the rating and switch multiple loads at a time on one switch, you can use the switches to operate relays that do the heavy lifting, the load switching.
 

Reubenski

TRD Off-Road Premium
New member
Joined
Nov 18, 2026
Threads
0
Messages
2
Reaction score
4
Location
Co
Vehicle(s)
2026 TRD ORP
Not what you're asking for, but might be what you need to hear: I wouldn't want to be constrained by the vehicles factory wiring and switches. The AUX switches are a cool idea but in all reality you probably, genuinely want aftermarket lighting on a seperate wiring harness to protect your vehicle. Using a conventional aftermarket, add-on wiring harness with a relay and fuse allows max flexibility and keeps aftermarket systems away from these modern vehicles complex and sensitive wiring and ECUs.

I wired a 20" light bar and the two fog lights on my '25 Tundra together and used a wiring harness with an appropriate fuse and relay. I just used Deutsch connectors and spliced wires where necessary.
 

Van Solo

TRD Off-Road Premium
Well-known member
First Name
Van
Joined
May 20, 2025
Threads
20
Messages
625
Reaction score
412
Location
Calgary / Canada
Vehicle(s)
4Runner
Hey everyone,

Looking for some advice from anyone who's wired up auxiliary lighting on the 6th gen 4Runner Hybrid, specifically using the factory Toyota AUX switches.

With BF around the corner, I'm planning to run:
  • 2x Baja Designs Squadron 2.0 Sport ditch lights
  • 1x Baja Designs 20” S8 light bar (lower Pro grille)
Ideally, I'd like to keep everything running through the factory AUX switches and Toyota pigtails. I'm trying to avoid adding something like a SPOD or Switch-Pros at this point, since I don't anticipate having a ton of additional accessories to wire up down the road.

My initial thought was to put all the main lights (both ditch lights + light bar) on one AUX switch, and all the backlight functions on another. That way, I can turn on the main lighting together, or just run the backlights independently.

A couple questions:
  1. Has anyone done something similar using AUX 1/2 vs AUX 3/4? Is there a reason to favor one set of switches over the other?
  2. Is there any reason I shouldn't combine the two ditch lights and the S8 light bar onto one AUX circuit? I can't really see this as an either/or situation. If I'm in a situation where I need the ditch lights, I'd probably want the light bar on as well. Seems more useful to have them come on together rather than use two separate switches.
  3. From an electrical standpoint, is the combined draw too much for a single factory AUX circuit?
  4. For the backlights, can the two Squadron backlights and the S8 amber backlight be tied into a single AUX switch? Any quirks with the Baja Designs harnesses I should be aware of?
Mostly looking for recommendations on how others have approached this, especially if you've done it on the Hybrid with the factory AUX wiring. I've been going back and forth on this idea for a while and needed to recruit your expertise and guidance.

Appreciate any advice, wiring diagrams, or pictures of your setups. Thanks!
@Diode Dynamics use the wireharness to connect to the AUX and your abble to rest assured yu will never have an issue (see our build and review)
Sponsored

 
 







Top