Sponsored

Clipse

TRD Off-Road Premium
Well-known member
Joined
Jul 28, 2025
Threads
2
Messages
48
Reaction score
34
Location
Seattle, WA
Vehicle(s)
2025 4Runner
Just wrapped up the MT64 install on my TRD ORP Hybrid, along with the DrKDSS track bar correction bracket. Figured I'd share some initial thoughts after getting a little seat time on the road.

Coming from the factory Off-Road Bilsteins, the first thing I noticed is that the OME setup feels considerably softer. The MT64s seem to do a really nice job absorbing bumps and smoothing out the roughness of uneven roads. Overall, the ride feels much more plush and comfortable, but also a bit looser than the factory setup.

I'm wondering if some of that looseness is coming from the higher ride height, but the rear definitely feels a bit more bouncy than I expected.

I also have to agree with OP's assessment that ARB may not have fully accounted for the additional weight of the hybrid. The rear seems to sit a little lower than I'd ideally like. I can see why you opted for the Robinson spacer to help compensate for that.

What setting do you have your light adjusters/dials set to? I'm currently running around 3–4 and curious how that compares.

Obviously, these are just initial on-road impressions. I'll need to put some more miles on them and get them off-road before drawing any real conclusions. So far, though, the improvement in ride comfort is noticeable!
Sponsored

 
OP
OP
Van Solo

Van Solo

TRD Off-Road Premium
Well-known member
First Name
Van
Joined
May 20, 2025
Threads
20
Messages
625
Reaction score
412
Location
Calgary / Canada
Vehicle(s)
4Runner
Just wrapped up the MT64 install on my TRD ORP Hybrid, along with the DrKDSS track bar correction bracket. Figured I'd share some initial thoughts after getting a little seat time on the road.

Coming from the factory Off-Road Bilsteins, the first thing I noticed is that the OME setup feels considerably softer. The MT64s seem to do a really nice job absorbing bumps and smoothing out the roughness of uneven roads. Overall, the ride feels much more plush and comfortable, but also a bit looser than the factory setup.

I'm wondering if some of that looseness is coming from the higher ride height, but the rear definitely feels a bit more bouncy than I expected.

I also have to agree with OP's assessment that ARB may not have fully accounted for the additional weight of the hybrid. The rear seems to sit a little lower than I'd ideally like. I can see why you opted for the Robinson spacer to help compensate for that.

What setting do you have your light adjusters/dials set to? I'm currently running around 3–4 and curious how that compares.

Obviously, these are just initial on-road impressions. I'll need to put some more miles on them and get them off-road before drawing any real conclusions. So far, though, the improvement in ride comfort is noticeable!
Light setting to .5 or 1
 

verendus

TRD Off-Road Premium
Member
Joined
Aug 7, 2026
Threads
2
Messages
14
Reaction score
14
Location
Northern California
Vehicle(s)
2026 4Runner TRD ORP
Just wrapped up the MT64 install on my TRD ORP Hybrid, along with the DrKDSS track bar correction bracket. Figured I'd share some initial thoughts after getting a little seat time on the road.

Coming from the factory Off-Road Bilsteins, the first thing I noticed is that the OME setup feels considerably softer. The MT64s seem to do a really nice job absorbing bumps and smoothing out the roughness of uneven roads. Overall, the ride feels much more plush and comfortable, but also a bit looser than the factory setup.

I'm wondering if some of that looseness is coming from the higher ride height, but the rear definitely feels a bit more bouncy than I expected.

I also have to agree with OP's assessment that ARB may not have fully accounted for the additional weight of the hybrid. The rear seems to sit a little lower than I'd ideally like. I can see why you opted for the Robinson spacer to help compensate for that.

What setting do you have your light adjusters/dials set to? I'm currently running around 3–4 and curious how that compares.

Obviously, these are just initial on-road impressions. I'll need to put some more miles on them and get them off-road before drawing any real conclusions. So far, though, the improvement in ride comfort is noticeable!
I am surprised that you find the new suspension softer. What are your tire setup? I installed ome factory trailhunter suspension on my orp gas and the ride became much more tout and stiffer. Although the onroad ride is very smooth, I can definitely feel the stiffness of the rear springs. This may be due to shedding about 400lbs of the hybrid battery. Offroad ride has been fantastic with a full load out at about 500lbs.

The onroad stiffness for me has to do with my c load toyo opencountry tires. The side walls are definitely stiffer than the stock. I just can't imagine the mt64 being softer than the stock.
 

Clipse

TRD Off-Road Premium
Well-known member
Joined
Jul 28, 2025
Threads
2
Messages
48
Reaction score
34
Location
Seattle, WA
Vehicle(s)
2025 4Runner
I just got my alignment done yesterday, so I've been rolling on stocks the last 2 days. About to put on Nitto Terra Grappler g3s 35x12.5 C rated setup today and can report back. I can't imagine the wheels/tire will make the suspension feel stiffer.
 

Clipse

TRD Off-Road Premium
Well-known member
Joined
Jul 28, 2025
Threads
2
Messages
48
Reaction score
34
Location
Seattle, WA
Vehicle(s)
2025 4Runner
I just got my alignment done yesterday, so I've been rolling on stocks the last 2 days. About to put on Nitto Terra Grappler g3s 35x12.5 C rated setup today and can report back. I can't imagine the wheels/tire will make the suspension feel stiffer.
I stand corrected! Not sure if it’s a combination of the suspension settling in, the bigger tires, or both, but this setup feels SO much better now. The bounciness I mentioned in my initial impressions is pretty much gone, and the truck feels significantly more planted. I’m genuinely impressed with how easily this platform rolls on 35s. Also pleasantly surprised by how little trimming was actually needed to make everything fit. Just pushed the front liners forward and trimmed off the two tabs with the metal fasteners.

Just installed the Perry Parts rear bump stops this morning with the recommended 1” spacer. Hopefully that’ll take care of any bottoming out when going over curbs or larger compressions.

Overall, really happy with how this setup is coming together. The MT64s and 35s are a great combination so far. Looking forward to getting them off-road!
Sponsored

 
 







Top