Recent content by rocktheroad

I haven’t seen anything on the market yet, that could fit there. I got 360 lights as an option for the Roof Rack, and they include two lights designed for the Tacoma, which are supposed to brighten up the truck bed. I was considering connecting it to the Diode Dynamics hitch break light, so I’d...

This is driving me crazy, and it is not just about Prinsu… It is about most of roof racks… I have Cali Raised roof rack, and I don't even have sunroof… They have their version of tent mounts, which I think is still too low. https://caliraisedled.com/products/roof-rack-rtt-mounts

We are in the same boat :) I even managed to break the closing lid of the D-Switch right after I opened the package. So, I’ll wait until someone figures it out. I’ll post here if I find any other information!

Did you had any progress on this? I just got mine D-Switch, and I was trying to figure out this too…. Here is what I found, and keeps me puzzled: D-Switch sensor wires need a simple +12V signal, not CAN/LIN/message-based signals. The D-Switch guide says the accessory harness sensor wires...

I know its not that relevant to this thread, but I just ordered this jack nuts/rivnuts - never used it, but goal is to use 4 of these To mount 4 anchor points for bluetti charger here: Is this plastic trim firm enough? I did some research and this are lightest jack nuts out there…

This is a great overlanding setup! I was considering vent orientation, which is why I like the sunken area on the left, as It will still give room if I put a large suitcase next to the wheel arch. Do you think it needs some space on the back part (where there’s no vent)? I might add some...

Hi guys, I just got the Bluetti Car Charger 2, and I’m trying to decide where to put it so it doesn’t get dinged or hit by suitcases, beach chairs, and other things. This spot looks good, although charger might be a bit smaller than in the picture. The wiring comes from the bottom. I could turn...

Just to confirm, when you install this flush in a 6th gen 4Runner, you won’t be able to use your locking pin to keep it in place. I’m not too concerned about it slipping out without the pin, but I’m a bit worried about what to do when I need to tow - it’s a bit tricky to get it out.

I am looking for something similar, but I want folding hinge, something like Croc Hinge. I want to stove away awning on top of roof top tent, and fold down when I am using it… But this guys are in Australia… And even in australian dollars they are waaaay cheaper I'll create Aligator Hinge here...

No any updates… i just installed smaller wiper blades, and they’re working great! Now, I have a bit more space for wires on both sides of the vehicle. The plan remains the same - run wires on both sides, one for the LED bar and the other for the 360 lights. However, I was a bit let down when I...

Yup, it startles me from time to time… What bothers me more is the vibration of the hood, as that is the next thing I start looking for when it happens… Wipers solve the first issue, but I have no idea how to sort out that trembling of the hood…

I am so lame... I haven't connected them yet. I am planning to run wires down both sides of the windshield, one for the front LED bar, and another side for 360 lighting. They can't both fit into the wire hider cover I have: But I ran into a problem, as there is not enough space on the...

It seems like you might have the wrong front bracket. Mine is almost touching the roof! @odins_beer had a similar issue and they sent him the correct bracket.

I keep forgetting to take some pics when it is daylight... here are two that I had on my phone. This is with the front valance in the closed position... Hopefully, I will remember to take better pictures, and the one with the visible led bar.

I have led bar and 360 light on mine... :(